Inclined Powered
STANDARD SPECIFICATIONS
• Transporting between floors
• Booster conveyor for gravity
flowsystems
• Heavier loads can be
conveyed because of less
friction build-up
• Booster conveyor for gravity
flowsystems
• Heavier loads can be
conveyed because of less
friction build-up
Applications / Features:
Belt - 12", 16", 18", 20", 24" and 30" wide rough-top belt.
Bed - Roller bed with 1.9" diameter x 16 gauge galvanized rollers spaced on 6" centers. Rollers mounted in 7" x 1-1/2" x 12 gauge powder painted formed steel channel frames. Frames bolted together with butt couplings.
Under-Trussed Bed - Extra reinforcement to prevent sag in longer bed sections in addition to reinforcing angles,
20 feet and longer.
X-Bracing - Supplied on conveyors 40 feet and longer. Used to square bed sections to insure proper product and belt tracking.
Double Nose-Over - Adjustable from 0° to 30°.
Center Drive - Mounted below conveyor bed section. Can be placed most anywhere in conveyor length.
Tail Pulley - 4" diameter, crowned with 1-3/16" diameter shaft through 30" wide belt. 6" diameter tail pulley with 1-7/16" diameter shaft turned down on ends for wider than 30" belt.
Drive Pulley - 8" diameter and fully lagged, 1-7/16" diameter shaft.
Snub Roller - 2-1/2" diameter at drive pulley, 2" diameter at terminal pulleys.
Return Roller - 1.9" diameter.
Take-Up - Located in center drive, provides 24" of belt take-up.
Gravity Brackets - Adjustable rod with 1-3/8" diameter pop-out transfer roller to attach wheel or 1-3/8" diameter roller conveyor.
Bearings - Sealed prelubricated with cast iron housings.
Floor Supports - Adjustable 31-1/2" to 45-1/2" from floor to top of belt. One support supplied at each end of conveyor and at noseover, with knee braces.
Speed Reducer - C-Face mounted heavy duty worm gear reducer.
Motor - 3/4 HP 230/460-3-60 TE motor.
Belt Speed - 60 FPM constant.
Capacity - See Load Capacity Chart.
(For Optional Equipment, Weight Specifications, and Engineering Line Drawings, please see catalog pages, above).
Bed - Roller bed with 1.9" diameter x 16 gauge galvanized rollers spaced on 6" centers. Rollers mounted in 7" x 1-1/2" x 12 gauge powder painted formed steel channel frames. Frames bolted together with butt couplings.
Under-Trussed Bed - Extra reinforcement to prevent sag in longer bed sections in addition to reinforcing angles,
20 feet and longer.
X-Bracing - Supplied on conveyors 40 feet and longer. Used to square bed sections to insure proper product and belt tracking.
Double Nose-Over - Adjustable from 0° to 30°.
Center Drive - Mounted below conveyor bed section. Can be placed most anywhere in conveyor length.
Tail Pulley - 4" diameter, crowned with 1-3/16" diameter shaft through 30" wide belt. 6" diameter tail pulley with 1-7/16" diameter shaft turned down on ends for wider than 30" belt.
Drive Pulley - 8" diameter and fully lagged, 1-7/16" diameter shaft.
Snub Roller - 2-1/2" diameter at drive pulley, 2" diameter at terminal pulleys.
Return Roller - 1.9" diameter.
Take-Up - Located in center drive, provides 24" of belt take-up.
Gravity Brackets - Adjustable rod with 1-3/8" diameter pop-out transfer roller to attach wheel or 1-3/8" diameter roller conveyor.
Bearings - Sealed prelubricated with cast iron housings.
Floor Supports - Adjustable 31-1/2" to 45-1/2" from floor to top of belt. One support supplied at each end of conveyor and at noseover, with knee braces.
Speed Reducer - C-Face mounted heavy duty worm gear reducer.
Motor - 3/4 HP 230/460-3-60 TE motor.
Belt Speed - 60 FPM constant.
Capacity - See Load Capacity Chart.
(For Optional Equipment, Weight Specifications, and Engineering Line Drawings, please see catalog pages, above).
MODEL "190RBI"
Inclined Roller Bed
Conveyor
Inclined Roller Bed
Conveyor
STANDARD SPECIFICATIONS
Engineering Data
